|
|
輸送機的故障處理 Fault handling of conveyor※跑偏的原因有多種，需根據不同的原因區別處理。 第 一 ： 調整承載托輥組 第 二 ：安裝調心托輥組 第 三 ：張緊處的調整 皮帶張緊處的調整是皮帶輸送機跑偏調整的一個 非常 重要的環節。 第 四 ：調整驅動滾筒與改向滾筒位置 驅動滾筒與改向滾筒的調整是皮 帶跑 偏調整的重要環節 第 五 ：雙向運行皮帶輸送機跑偏的調整 ※皮帶打滑的處理辦法： 第 一 ：螺旋張緊或液壓張緊皮帶機的打滑使用螺旋張緊或液壓張緊的皮 帶 輸送機出現打滑時可調整張緊行程來增.大張緊力。但是，有時張緊 行 程已不夠，皮帶出現了永.久性變形，這時可將皮帶截去一段重新進 行 硫化。 第 二 ：在使用尼龍帶或EP是要求張緊行程較長，當行程不夠時也可重新 硫 化或加大張緊行程來解決。 第三：重錘張緊皮帶輸送機皮帶的打滑使用重錘張緊裝置的 皮 帶輸送機在皮帶打滑時可添加配重來解決，添加到皮帶不打滑為止 。 但不應添加過多，以免使皮帶承受不必要的過大張力而降低皮帶的 使 用壽命。 ※ there are many reasons for deviation, which should be handled differently according to different reasons. First: adjust the bearing idler group Second: install the self-aligning idler group Third: adjustment of belt tension adjustment of belt tension is a very important link of belt conveyor deviation adjustment. Fourth: adjust the position of the driving drum and the reversing drum. The adjustment of the driving drum and the reversing drum is an important link in the belt deviation adjustment Fifth: adjustment of deviation of two-way running belt conveyor ※ handling method of belt slip: First: slip of spiral tensioned or hydraulic tensioned belt conveyor. In case of slip of spiral tensioned or hydraulic tensioned belt conveyor, the tensioning stroke can be adjusted to increase High tension. However, sometimes the tensioning stroke is not enough and the belt appears permanent In case of permanent deformation, a section of the belt can be cut off and vulcanized again. Second: when using nylon belt or EP, the tensioning stroke is required to be long. When the stroke is not enough, it can also be re vulcanized or increased. Third: the belt slip of the heavy hammer tensioning belt conveyor. The belt conveyor with the heavy hammer tensioning device can add a counterweight to solve the belt slip until the belt does not slip. However, too much should not be added, so as not to make the belt bear unnecessary excessive tension and reduce the service life of the belt. |
